Polyurethane Rubber Tube: Properties, Applications, and Custom Options
If you’re comparing PU tube against standard rubber or PVC tubing for a pneumatic, fuel-line, or fluid-transfer job, you’ve probably noticed many manufacturers answer with a spec table instead of a reason to pick one durometer or formulation over another. That gap matters more than it looks — the same general material family covers everything from a soft, kink-resistant pneumatic line to a hard, structurally loaded wear part, and picking the wrong end of that range costs you either flexibility or service life. For broader context on cast polyurethane stock shapes, see our guide to polyurethane boards, sheets, and rods.
Polyurethane rubber tube is a flexible, wear-resistant tubing material used in pneumatic controls, fuel lines, and industrial fluid-transfer systems. Durometer hardness ranges from 80A to 70D, and tensile and tear strength both rise with hardness, letting engineers match tube flexibility to load and wear demands for each application.
Below, we cover the two levers that actually decide fit: how the 80A–70D hardness range trades flexibility for strength, and how polyether and special-polyester TPU chemistries diverge on temperature and abrasion performance. Then we walk through where PU tube fits — and doesn’t — across pneumatic, food-contact, and adjacent product categories, and how to source a custom grade instead of picking from a standard list.
1. Material Properties and Durometer Selection
Pepson casts polyether-type TPU tube across a hardness range from 80±3 to 95±3 Shore A (grades E580A–E595A), then continues into 55±3 to 70±3 Shore D (grades E598A–5470D). That’s one product family covering everything from a soft, flexible pneumatic-line hardness through a rigid wear-part hardness — which matters because the mechanical properties don’t stay flat across that range.
Tensile strength climbs from 320 kg/cm² at 80A up to 500 kg/cm² at 70D, and tear strength scales from 80 kg/cm² to 200 kg/cm² over the same span. That’s the quantitative basis most manufacturer spec tables — PSI, Polyconn, FixSupply among them — leave out when they simply list durometer options without explaining what each one buys you.
The trade-off is direct: a softer tube (80A–90A) bends further before it kinks, but it carries less tensile and tear load. A harder tube (95A–70D) resists tearing and structural stress, but gives up flex range. Neither end is “better” — it depends on whether your application is routing-constrained or load-constrained.
Tube-wall hardness itself is measured by the durometer indentation method defined in ASTM D2240, which is what grounds “80A” and “70D” as standardized readings rather than vendor-specific marketing labels. For the general framework behind matching durometer to application, our guide to polyurethane material selection covers the same specification logic this section applies specifically to tube.
Reading the Durometer-to-Strength Curve
Plot it in plain terms: every step up in Shore hardness from 80A to 70D buys tensile and tear strength at the cost of flex range and kink resistance. There’s no hardness that maximizes both — durometer is a trade-off axis, not a single “better” direction.
For a specifier, that means a tube chosen purely for flexibility will tolerate less tensile load and tear stress than one chosen for durability. Know which constraint drives your application before you default to a mid-range durometer.
Matching Hardness to the Application
Flexible, low-durometer grades (80A–90A) suit pneumatic control lines and tight-radius routing, where kink resistance matters more than raw strength. Higher-durometer grades (95A–70D) suit wear-part or structurally loaded tube runs, where tensile and tear strength outweigh flexibility.
If your application sits between those two profiles, confirm your load, wear, and bend-radius targets with Pepson engineering before defaulting to a mid-range durometer — a few degrees of Shore hardness in either direction changes the trade-off more than it looks like it should.
For engineers: Have a technical challenge? Talk to our engineering team
2. Polyether vs. Polyester TPU: Choosing the Right Formulation
Most manufacturers treat “polyurethane” as a single material class. Pepson’s polyether and special-polyester TPU chemistries diverge enough on temperature range and abrasion resistance that the choice between them can change a sourcing decision — not just a spec-sheet detail.
Polyether Polyurethane Tubing: Standard-Duty Performance
Polyether-type TPU carries a service range of −40°C (−40°F — the only temperature where the two scales coincide) to 80°C (176°F), which serves as the general-purpose baseline for pneumatic and fluid-transfer tube. It fits applications where oil exposure and abrasion duty are moderate rather than extreme — the special-polyester grade below is the upgrade path once either factor becomes a limiting condition.
Special Polyester Polyurethane Tubing: Abrasion and Oil Resistance
Special polyester-type TPU extends the service range to −50°C (−58°F) to 80°C (176°F) and adds oil, flex, and abrasion resistance beyond the polyether baseline. In Taber abrasion testing (H-22 wheel, 1 kg load, 1,000 revolutions), special polyester TPU measured 18–55 mg of abrasion loss — the lowest of Pepson’s three TPU families.
Reach for special polyester TPU where cold-climate service, oil exposure, or high-abrasion routing pushes past what standard polyether tube is rated to handle.
3. Applications of Polyurethane Rubber Tube
The three headline uses from the durometer and formulation guidance above are pneumatic controls, fuel lines, and industrial fluid transfer — and the right grade for each depends on the hardness and formulation choices covered in sections 1 and 2, not on a generic “PU is tough” claim.
One distinction worth flagging directly: automotive windshield and glazing work uses urethane adhesive — a chemical sealant tested for lap-shear and peel-adhesion strength under standards like SAE J1836 — not PU tube. If you found this page searching for “urethane tube for windshield,” you’re most likely after a windshield-bonding adhesive rather than tubing, which is a different product entirely. See the FAQ below for the full distinction.
Potable-water suitability is also conditional rather than automatic — see the FAQ below for what certification to check before specifying tube for a drinking-water line.
Industrial Pneumatic and Fluid-Transfer Uses
Kink resistance is one of the most common reasons buyers pick PU tube over standard rubber hose for pneumatic and fluid-transfer routing. Vendors typically attribute this to polyurethane’s flexural “memory” — its tendency to spring back to shape rather than staying kinked — though the specific mechanism isn’t independently confirmed outside vendor literature. What is measurable is the service range: −40°C (−40°F) to 80°C (176°F) for polyether-grade tube, or −50°C (−58°F) to 80°C (176°F) for special polyester — the more reliable number to design a cold-environment routing decision around.
For applications where rod stock is a better fit than tube — solid structural or bearing components rather than a hollow fluid path — see applications of polyurethane rods for the comparison.
Food-Contact and NSF-Certified Uses
Polyether-type TPU formulations intended for wet or fatty food contact are typically qualified against 21 CFR 177.2600, the FDA regulation covering rubber articles intended for repeated food-contact use. Food-and-beverage tubing can also carry NSF/ANSI 51 certification, which sets minimum public-health and sanitation requirements for tubing, seals, and other food-zone components.
Neither certification is automatic for a given durometer or formulation — confirm the specific grade carries the qualification your application needs before specifying it for food or beverage service.
4. Custom Options and Sourcing
Custom sizing and cutting are available across the full durometer range covered in Section 1. If you’re standardizing tube alongside other cast stock shapes, our custom sizing and cutting services cover the same process applied across sheets, rods, and tube.
Going straight to Pepson as the manufacturer — rather than a distributor or regional stockist — is usually the more direct path when you need a specific durometer, formulation, or dimension rather than whatever a catalog happens to carry off the shelf. See the FAQ below for more on sourcing.
If your application has a specific load, wear, or chemical-exposure profile, request a durometer and formulation recommendation directly rather than picking from a standard-grade list. That reinforces the same trade-offs covered in Sections 1 and 2, applied to your actual spec instead of a generic one.
For procurement: Ready to source? Request a quote from Pepson
5. FAQ
How do you seal or bond polyurethane rubber tube?
There’s no single universal method — it depends on the fitting system, pressure rating, and environment your assembly runs in. Because bonding and sealing methods aren’t standardized across polyurethane tube applications the way material specifications are, the fastest path to a reliable joint is to confirm the recommended fitting or bonding approach with Pepson engineering for the specific grade and durometer you’re specifying.
Can polyurethane rubber tube be used for automotive windshield trim or glazing?
No — that’s a different product category. Automotive windshield and glazing work uses urethane adhesive, a chemical sealant tested for lap-shear and peel-adhesion strength under standards like SAE J1836, not PU tube, which is an extruded or cast tubular product built for pneumatic and fluid-transfer duty. If your search led you here looking for a windshield-bonding adhesive, you’ll want that product category instead.
Is polyurethane tubing safe for water or potable-water applications?
Not automatically — food and drinking-water contact requires the tube to carry the right certification, not just the right base material. Polyether-type TPU intended for wet or fatty food contact is typically qualified against 21 CFR 177.2600, the FDA rule covering rubber articles in repeated food contact, and food-and-beverage tubing can carry NSF/ANSI 51 certification confirming it meets public-health and sanitation requirements. Ask for the specific certification on the grade you’re specifying rather than assuming standard PU tube qualifies.
Where can I buy polyurethane rubber tube, or find a local supplier?
Rather than sourcing through a regional stockist or catalog reseller, you can go directly to Pepson as the manufacturer. That gets you a custom durometer, formulation, and dimension match instead of picking from whatever a distributor happens to stock — and it’s typically a faster path to a quote for non-standard sizes.
Conclusion
Durometer (80A–70D) and formulation (polyether vs. special polyester) are the two real selection levers for this material — not a single polyurethane-vs-rubber comparison, and not a spec table read in isolation. Get those two right and the application fit — pneumatic, fuel-line, fluid-transfer, or food-contact — follows from them.
Pepson casts tube across the full 80A–70D range in both polyether and special-polyester TPU, so the hardness conversation and the formulation conversation happen against the same set of numbers, direct with the manufacturer rather than through a distributor’s standard catalog.
